SG sensor CL3 double

 KIMAX accessories

Axle load sensor kits includes:

Double SG sensor CL3 Part number 10251

2 x SG sensor CL

1 x extension cable 3 m, connector both ends

1 x Y-splitter

2 x stainless steel cover

SG sensor

The SG sensor is a strain gauge based sensor, which transforms the strain of a beam to a current signal.

Axle load sensor

A typical application for the SG sensor is measuring the strain on a rear axle of a truck or a bus. When the strain is converted to a current the actual axle load can be calculated.


The SG sensor is program-able, through the Sensor Control Unit you can change slope from positive to negative, you can adjust offset as well as adjust gain of the SG sensor.

How to install

The SG sensor is bonded to the axle in which the strain is to be measured. It is crucial that the bonding to the axle is good. Grease, paint and corrosion protection must be removed before the actual bonding of the SG sensor is carried out.

After bonding and test of the functionality of the SG sensor, the sensor has to be sealed and best of all protected by stainless steel cover.

Bonding of the SG sensor can be done with an epoxy glue. We generally recommend using gluing set provide by us.

Where to install

SG sensors are typically installed on steering front axles for trucks or on springs for kimax spring groups.

Go to: for additional information and installation procedure.

Strain measurement

Kimax 1 uses the linear interrelatio

Basic operation

Depending on load of the vehicle

Leave spring suspended traction axle for Kimax 1

next text

SG sensor on parabolic rear axle suspension

Double SG sensor kit P/N 10251 includeDouble SG sensor with Y-splitter

2 x SG sensor CL

1 x Extension cable 3 meter, connector both ends

1 x Y-splitter

2 x Stainless steel cover

This kit is commonly used for group of two rear axles in combination with a Kimax 2 sensor installed on the chassis.

Extension cable has connector in both ends.

Y-splitter connect both SG sensors in parallel.

Electrical connection

Double SG sensor installation

Steering front axle installation

SG sensor installation on a steering front axle take typically place by use of one SG sensor on the topside of the axle at the vehicles center line. Cable has to be routed safely from axle to chassis beam taking the up and down movements in account.

Rear axle group installation

Size of your truck and type of your rear axle suspension system dictate our recommendation for best SG sensor installation.

  • Light 2 axle trucks typical up to 10 Ton, we recommend the SG sensors installed directly on the axle next to the spring support in left and right side
  • Standard 2 axle trucks 10 – 18 ton, we recommend the SG sensors installed on either springs or installed on the axle, decicion depends on actual type of springs.
  • Heavy 3 or 4-axle trucks above 18 ton, we always recommend the SG sensor installed on the springs. Common spring systems is classic parabolic springs or trapeze springs.

Output signal from two SG sensors at a rear axle group are to be connected in parallel adding output current from both sensors together as a common sensor signal.

Configuration of SG sensors

Through a Sensor Control Unit (SCU) you can adjust following parameters of the SG sensors:

  • Positive or negative slope, positive slope is selected for topside installation on front axles and parabolic springs, negative slope is selected installation on bottom side of parabolic springs or trapeze springs
  • OFFSET output signal, output signal is typically set to 15% of output range ( 3mA)
  • Reduce GAIN, gain in sensor can be reduced in steps in case your output signal saturate at max output current before max load is reached.

Factory setting for the sensors are positive slope, offset at 3 mA and gain at max.

Visit – order by Part Number for identifying sensor configurations equal to your truck.

Technical Specifications


Supply voltage 9 – 15 V direct current
Current consumption max 11 mA (without output signal)
Output Signal 0-20 mA
Max output signal 23 mA
Max load resistance 250 Ω @ 12 V supply
Active sensing area 12 x 20 mm
Input @ 20 mA out 2.500 µS
Dimmension ex. cable 51 x 22 x 8 mm
Operating temperature -30°C to +60°C
Storage temperature -40°C to +70°C
Cable length 2,7 m
Weight approx. 250 g
Protective class IP67 Sealed by stainess steel cover
Approval CE and E1


Kimax 1 and Kimax 2 are a series of high quality well proven on-board scales for use on trucks, buses and loading equipment. For detailed product selection guide please go to Kimax 1 and Kimax 2 are registered trademarks owned by Sense-Tech Weighing Systems.

Sense-Tech Weighing Systems are used all over the world. From the hectic harbours of Amsterdam to the dusty outback of Australia. And everywhere in between.

Sense-Tech Weighing Systems ApS
Bygade 43A
DK-7173 Vonge

Monday – Thursday: 8:00 – 16:00 CET
Friday: 8:00 – 14:00 CET