Kimax 2 radio 1 + 1×2 air
Part number 031200-0131
1 x display unit, cabin
1 x mounting frame + connection cable
3 x angle fittings
3 x air pressure throttle dia. 6mm
3 x T-fitting dia. Ø 8mm / 6mm / 8mm
Kimax 2 radio display and Kimax 2 sensor 1 + 1×2 air
Part number 030000-0140
1 x display unit, cabin
1 x mounting frame + connection cable
Part number 051200-01B1
3x angle fittings
3 x air pressure throttle dia. 6mm
3x T-fitting dia. Ø 8mm / 6mm / 8mm
and offer you a load control of you vehicle, either as a solo instrument including build in air sensors or as a display unit which needs contact to one or more Kimax 2 Sensors through the power line device bus, which can act on the existing electrical system on your vehicle.
Kimax 2 has two separately adjustable alarm levels. Exceeding alarm level 1 is indicated by a flashing diode for the individual axle which has exceeded its limit.
Alarm 2 switches in an internal electronic “relay” when the total weight for the vehicle is exceeded. The relay signal can be used as ON/OFF input for another unit, for example a tracking GPS or a tachograph.
Kimax 2 helps to achieve economical transportation, avoids fines and simultaneously optimizes the cargo weight.
* Tractor/trailer readings call for a Kimax 2 radio installed in the truck and a Kimax 2 sensor installed on the trailer.
Kimax 2 uses the linearity between air pressure and load of the single axles.
By using two reference points for each axle (empty weight and weight at maximum load) and the currently measured air pressure, Kimax 2 calculates the current axle load with an accuracy of 2 % of the maximum load for each axle.
Depending on load of the vehicle, the level valve maintains a constant height of the chassis above ground surface by regulating the pressure in the air bellows.
Front axle works typical with a single air circuit, the rear axle works typically with a dual air circuit
Air tubes are routed into the cabin
1 air sensor for the front axle and 2 air sensors for rear axle offer you the best accuracy. The influence of inclination or slightly uphill/downhill standing is partly compensated in this configuration, as well as weighing accuracy is unaffected on the distribution of goods loaded on the vehicle.
No air tubes inside the cabin
1 air sensor for the front axle and 2 air sensors for rear axle are connected to Kimax sensor box on the chassis. Sensor box communicate weight data with Kimax display inside the cabin.
On all vehicles you get optimal accuracy with two independent air inlets for
each axle, one for each pneumatic circuits (right and left) per axle or axle
group on air suspended axles, Kimax 2 calculates the current axle load on
each axle from two reference values LO and HI.
• When less accuracy is enough for you, one air inlet on each axle or axle
group is available too.
Kimax 2 is exactly as flexible as your vehicle:
Do you have a tractor equipped with air suspension on both front axles
and rear axles combined with a lift axle? No problem!
Do you have a truck with 2 front axles equipped with steel springs and
two rear axles divided in left hand and right hand air circuits? No
problem!
Do you want to couple a trailer or semitrailer on the above vehicles?
No problem!
Do you want to couple a low bed trailer equipped with hydraulic
suspension on a tractor equipped with air suspension? No problem!
Do you want to swap from one trailer to another trailer? No problem!
– Individual calibration values are stored in the Kimax unit on each
vehicle.
Kimax 2 Radio are able to communicate with both Kimax 2 Universal and
Kimax 2 Sensor as input devices
Kimax 2 output units is RS-232 thermal printer or 433 MHz
Wireless terminal.
Visit www.kimax.com for more details and information.
Supply voltage | 10 – 30 V direct current |
Current consumption | max 90 mA |
Alarm 1 | Flashing display |
Alarm 2 | output open collector NPN max 0.2A/ 50 VDC |
Display | Three-digits 7-segment LED character height 20.3 mm |
Accuracy | 2% of maximum load at 0 °C – +50 °C |
Air connection | quick release, 6 mm hose |
Maximum pressure | 15,5 bar (225 psi) |
Operating pressure | range 0-10,5 bar (0-150 psi) |
On-board computer | RS-232 serial |
Printer | RS-232 serial |
Device bu | Power line communication |
Operating temperature | -25°C to +70°C |
Storage temperature | -40°C to +70°C |
Dimensions | 182 x 53 x 75 mm |
Weight | approx. 550 g |
Protective class | IP60 |
Approval | CE and E1 |
Kimax 1 and Kimax 2 are a series of high quality well proven on-board scales for use on trucks, buses and loading equipment. For detailed product selection guide please go to Kimax.com. Kimax 1 and Kimax 2 are registered trademarks owned by Sense-Tech Weighing Systems.
Sense-Tech Weighing Systems are used all over the world. From the hectic harbours of Amsterdam to the dusty outback of Australia. And everywhere in between.
Sense-Tech Weighing Systems ApS
Bygade 43A
DK-7173 Vonge
Denmark
Monday – Thursday: 8:00 – 16:00 CET
Friday: 8:00 – 14:00 CET